README.md
]]>]]>  ]]>]]>

EXC - EXtendable Controller (Erweiterbarer Mikrocontroller)

The EXC is a microcontroller board with an ATmega16A/ATmega164A. The Board can be powerd over USB or from an external Source (9-15V) and used with common Voltages of 3V3 or 5V. Over the USB port it is also possible to establish a serial (uart) connection to a computer. The Board itself offers a SPI, I2C interface for bus systems, a interface for connection to external interrupts of the microcontroller and a analog interface for reading analog data into the microcontroller. At DP1 a Display can be connected to the board. The available demo firmware offers a quick demonstartion of the board functionallity. Check the Software section to get more information.




  
Experience
  
Level




  
Soldering
  



  
Software
  





Downloads




  
Type
  
File
  
Description




  
Schematic
  
]]>pdf]]> / cadlab
  
Schematic files


  
Board
  
]]>pdf]]> / cadlab
  
Board file


  
Drill
  
]]>pdf]]>
  
Drill file


  
Gerber
  
]]>zip]]> / ]]>tar]]>
  
Gerber/Drill files


  
Firmware
  
]]>zip]]> / ]]>tar]]>
  
Firmware for ATmega164A




Hardware

The pcb is created with KiCAD. All files are built with github actions so that they are ready for a production environment.

PCB

The circuit board is populated on one side. The best way for soldering is within a vapor phase soldering system.

Top Layer



Bottom Layer



Configuration

With Jumper J13 the EXC system is getting bus powered (5V). If the system runs with 5V jumper J12 has to be shorten between 2-3. When the system is driven by an external source through the step-down converter the system voltage is switchable between 5V and 3V3 over the slider switch SW6. If 3V3 are choosen the jumper J12 should be shorten between 1-2.


  
Only change the state of SW6 with disconnected power source. Also check if jumper J12 is set correctly!


LEDs/I2C

To enable the LEDs LED0-1 jumper J10 has to be shorten. If the I2C interface should be used the jumper J10 has to be removed.

UART

The UART of the ATmega164A can be coupled with the USB/UART bridge or with the external UART interface at connector J5. To set the transmission over USB/UART bridge jumper J1 and J2 should be shorten between 1-2. For the external UART interface jumper J1 and J2 should be shorten between 2-3.

Display

The display can be powerd constantly over J99 shorten between 2-3 or controllabe over the microcontroller pin PA2 and J99 shorten between 1-2.

Programming

The Firmware of the EXC can be programmed with Microchip Studio over ISP with an ATMEL ICE connected to J9 of the EXC. It is necessary to power the board from outside either over USB or the external power supply during programming.

FUSES




  
Register
  
Value




  
HIGH
  
0xD8


  
LOW
  
0xFF




Software

Dataflow diagram



Structogram





Additional Information




  
Type
  
Link
  
Description




  
Display
  
]]>web]]>
  
Display for extendable controller


  
Microchip Studio
  
]]>web]]>
  
Download Page for Microchip Studio


  
Atmel ICE
  
]]>pdf]]>
  
Atmel ICE Datasheet


  
ATmega16A
  
]]>pdf]]>
  
Microchip ATmega16A Datasheet


  
ATmega164A
  
]]>pdf]]>
  
Microchip ATmega164A Datasheet




R. GAECHTER